Industry news

I. Daily Maintenance: Reduce wear and tear and extend service life

The core of daily maintenance is "prevention first", which involves reducing the adhesion of stains, controlling environmental humidity, lowering the frequency of cleaning and fiber damage.

Control the environmental humidity to prevent the fibers from getting damp and moldy

Sisal fibers have a strong water absorption capacity. A humid environment can easily cause the fibers to mold and develop an unpleasant odor (especially during the rainy season or near the bathroom). It is necessary to ensure good indoor ventilation and a dehumidifier can be used (with humidity controlled at 40% to 60%). If the carpet is laid in a damp area, it is recommended to place a waterproof and moisture-proof pad under the carpet to isolate the moisture from the ground. Avoid placing wet mops or wet items directly on the carpet. If they accidentally get wet, they should be promptly dried with a dry cloth.

Regularly vacuum to remove surface dust and debris

The surface of sisal carpets is prone to accumulate dust and hair. If not cleaned for a long time, it will cause the fibers to clump and affect the breathability. Suggestion

Use a vacuum cleaner (with a brush head, avoid strong suction heads) to vacuum along the fiber texture direction 2 to 3 times a week, with a focus on cleaning areas prone to dust accumulation such as under the sofa and at the door.

When vacuuming, avoid back-and-forth friction (sisal fibers are relatively brittle and repeated friction can easily lead to breakage and pilling). If you find that the fibers are tangled, you can gently comb them by hand before vacuuming.

Avoid long-term heavy pressure and direct sunlight

Circular carpet pads (with a diameter larger than that of the furniture legs) can be placed under the furniture legs to distribute pressure and prevent local fibers of the carpet from being deformed (once deformed, they are difficult to recover). Regularly move the positions of furniture to avoid long-term pressure on the same area.

Avoid exposing the carpet to direct sunlight for a long time (such as beside floor-to-ceiling Windows), as ultraviolet rays can cause sisal fibers to fade and become brittle. You can pair it with blackout curtains or turn the carpet over regularly (once every six months) to ensure even force and sun exposure.

Reduce the introduction of external stains when entering or leaving

Lay footpads at the entrance of the carpet (it is recommended to choose rubber-soled or short-haired materials to prevent the footpads from fading and contaminating the sisal) to reduce the entry of mud, sand and rainwater from the soles of the shoes. If family members wear outdoor shoes and walk on carpets, it is necessary to clean up the debris on the soles of the shoes in time to avoid sharp particles (such as small stones) scratching the fibers.

Ii. Stain Treatment: Respond promptly to prevent penetration and residue

Sisal fibers have large pores. If stains seep into the interior of the fibers, they will be difficult to clean and prone to leaving marks. The principle of "immediate treatment, suction first, then wipe, and cautious use of cleaning agents" should be followed.

1. Liquid stains (coffee, tea, fruit juice, oil stains, etc.

Step 1: Absorb the liquid to prevent it from spreading

When liquid is spilled, immediately press the stained area with a clean dry towel, paper towel or absorbent sponge (do not use a lint-shedding cloth) to absorb the liquid on the surface (do not wipe when pressing to avoid the stain spreading to the surrounding area). The dry towel can be changed multiple times until there are no obvious wet marks on the towel after pressing.

Step 2: Targeted cleaning to avoid damaging the fibers

Water-soluble stains (coffee, tea, juice) : Soak a clean cloth in warm water (below 30℃, avoid high temperature damaging the fibers), wring it out until it is half dry, and gently press the stained area (do not rub). Repeat 2-3 times until the stain fades. If there are still traces, add a small amount of neutral detergent (such as baby laundry detergent, with a concentration controlled below 1%) to warm water, stir well, then dip a cloth in it for cleaning. Finally, wipe off the remaining detergent with a clean cloth and use a dry towel to absorb the water.

Oily stains (cooking oil, lipstick, shoe polish) : First, sprinkle a layer of cornstarch or talcum powder on the stained area, let it stand for 1-2 hours (to absorb the oil), and then use a vacuum cleaner to suck up the powder. If there are any remaining marks, use a cotton swab to dip a small amount of medical alcohol (75% concentration), gently apply it to the stain (avoid extensive contact of alcohol to prevent the fiber from becoming brittle), and after the alcohol has evaporated, press and absorb it with a dry towel.

Step 3: Let it dry to prevent mold

After cleaning, open the Windows for ventilation or use a fan (with a low wind speed) to blow dry the stained area. Make sure the carpet is completely dry (for at least 24 hours) to avoid mold growth caused by moisture.

2. Solid stains (food residues, sand, ink, etc.)

Dry solid stains (food scraps, sand and mud) : First, use a vacuum cleaner to suck away the loose particles on the surface. If there are residues adhering to the fibers, gently pick them out with tweezers (do not pick by hand to avoid fiber breakage), and then wipe the remaining marks with a dry towel.

Ink stains: For a small amount of ink, you can use a cotton swab dipped in diluted white vinegar (white vinegar: water = 1:2) and gently apply it. After the stain fades, wipe it clean with a cloth and clean water. If the ink is deep, a small amount of special natural fiber carpet cleaner can be used (it needs to be tested on the corners of the carpet first to confirm that there is no fading before use). After cleaning, absorb the water in time.

3. Stubborn stains (mold spots

Mold spots: If mold spots occur due to moisture, first gently brush off the surface mold dust with a soft-bristled brush (to prevent the spread of mold), then mix a small amount of hydrogen peroxide (3% concentration, that is, medical hydrogen peroxide) with warm water, dip a cloth in it and gently press the mold spot area (hydrogen peroxide has a slight bleaching effect, so it needs to be tested in a concealed place first), let it stand for 5 minutes, then wipe it clean with a clean cloth, and finally let it dry completely.